Remove the interior assembly from your door and inspect the thinner cable for damage.If you see damage to the cable or you are still experiencing issues, call Kevo support. If you still see magenta after you've recalibrated, perform the following test: Remove your smart device or Kevo fob from your pocket or purse, hold it up close to outside of the Kevo lock, and touch the deadbolt.If the light ring no longer flashes magenta, recalibrate your smart device or Kevo fob once more.If the light ring still flashes magenta, the thinner cable inside the lock could be damaged. When calibrating, you want to stand at the distance that you normally would when you are locking/unlocking your Kevo with the smart device or Kevo fob in the same location it would normally be (i.e. If you are close enough to the door to unlock it manually with a key and you still see the magenta flash, then you should recalibrate your lock. ![]() First try repositioning your smart device or Kevo fob closer to the lock when locking/unlocking. This range is based on the calibration distance. This means that the smart device or Kevo fob that you are using is out of activation range. If you have SmartCode 888 and have not purchased it from us, please contact the manufacturer directly with any further questions you may have.I See A Magenta Flash On The Outside Of My Kevo When I Try To Lock/Unlock It only warrants and is only able to support products purchased directly from us. The information provided is for reference only and is not intended to be used as a substitute for professional advice. Please note that this is a user manual SmartCode 888 from Kwikset is provided as is and without warranty all information contained herein is provided by the manufacturer or the certifying body. After a few seconds, the lock will initiate the door handing process. The status LED will flash green and red several times.ĥ. Keep holding the button for 30 seconds until the lock beeps and the status LED flashes red.Ĥ. Press and HOLD the Program button while reinserting the battery pack.ģ. To perform a factory reset, please perform the following:Ģ. Please only perform a factory reset when the primary controller is missing or inoperable. When paired with a Z-Wave Plus home control system, you can monitor if the door is locked, get activity alerts, remotely change codes, access the door from. Factory reset SmartCode 888Ī factory reset will delete all user codes associated with the lock and will remove itself from your smart home system. The red LED will illuminate when the lock enters Remove mode.Įven though the lock is sleeping, all buttons are active and can be used to initiate any lock activity.įor the RF side, it will wake up every 1 second to check if there are any requests from your smart home controller. When prompted by the system, press button A” on the lock interior once. Please allow time for the controller to add the lock to your system.įollow your smart home system’s instructions to remove the lock from the network. The red LED will illuminate when the lock enters Add Mode. ![]() When prompted by your smart home system to add the lock, press button “A” on the lock interior one time. Having very little cons make this keypad deadbolt an ideal. ![]() It is simple, easy to use, has long battery life, has auto lock, easy to install and even has one time usage codes which is generally not found at these kind of keypad deadbots without smart capabilities and connection options. Initiate the process to add the lock to your system at your smart home controller. We really loved Kwikset 264 Contemporary Keypad Deadbolt. Supports Z-Wave SmartStart allowing you to setup the product simply by scanning its QR code via.Firmware updatable via a compatible Z-Wave gateway.Kwikset describes SmartCode 888 as having the following features: The following security modes are directly supported: If the door lock is not locking, there are a Pastor Kojo Frimpong: Welcome to The. As a Z-Wave Plus certified product, SmartCode 888 supports Z-Wave S2 security. Kwikset Deadbolt plays loud warning beep when locked.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |